AVR430/AVR630 harman/kardon
REAR-PANEL CONNECTIONS
! AM Antenna: Connect the AM loop antenna sup-a Center Speaker Outputs: Connect these outputs? Video 1 Video Inputs: Connect the composite or
plied with the receiver to these terminals. If an externalto the matching + and � terminals on your centerS-Video PLAY/OUT jacks of a VCR or other video
AM antenna is used, make connections to the AM andchannel speaker. In conformance with the CEA color-source to these jacks.
GND terminals in accordance with the instructions sup-code specification, the green terminal is the positive,
? Video 1 Video Outputs: Connect the composite
plied with the antenna.or O+� terminal that should be connected to the red
or S-Video REC/IN jacks of a VCR or other video
(+) terminal on speakers with the older color-coding.
? FM Antenna: Connect the supplied indoor or anrecording device such as a DVD recorder or PVR to
Connect the black (�) terminal on the AVR to the
optional external FM antenna to this terminal.these jacks.
black negative (�) terminal on your speaker.(See
page 16 for more information on speaker polarity.)
L Preamp Outputs: Connect these jacks to an° Video 2 Video Inputs: Connect the composite or
optional, external power amplifier for applications? Surround Back/Multiroom Speaker Outputs:S-Video PLAY/OUT jacks of a VCR or other video
where higher power is desired.These speaker terminals are normally used to powersource to these jacks.
the surround back left/surround back right speakers
c Subwoofer Output: Connect this jack to the line-? Video 2 Video Outputs: Connect the composite
in a 7.1 channel system. However, they may also be
level input of a powered subwoofer. If an external sub-or S-Video REC/IN jacks of a VCR or other video
used to power the speakers in a second zone, which
woofer amplifier is used, connect this jack to the sub-recording device such as a DVD recorder or PVR to
will receive the output selected for a multiroom system.
woofer amplifier input.these jacks.
To change the output fed to these terminals from
A-BUS Connector: Connect this jack to an optionalthe default of the Surround Back speakers to thea Video 3 Video Inputs: Connect the composite or
¨
A-BUS-certified remote room keypad or amplifier toMultiroom Output, you must change a setting in theS-Video PLAY/OUT jacks of a VCR or other video
extend the multiroom capabilities of your AVR 630.Advanced Menu of the OSD system.See page 36 forsource to these jacks.
See page 38 for more information on A-BUS.more information on configuring this speaker output.In
b Component Video Monitor Outputs: Connect
normal surround system use, the brown and black ter-
§ Surround Speaker Outputs: Connect these out-these outputs to the component video inputs of a
minals are the surround back left channel positive (+)
puts to the matching + and � terminals on your sur-and negative (�) connections and the tan and blackvideo projector or monitor. When a source connected
round channel speakers. In conformance with the CEAto one of the Component Video Inputs cd is
terminals are the surround back right positive (+) and
color-code specification, the blue terminal is the posi-selected the signal will be sent to these jacks.
negative (�) terminals. For multiroom use, connect the
tive, or O+� terminal that should be connected to the
brown and black SBL terminals to the red and black
c Component Video 1 Inputs: These inputs may
red (+) terminal on the Surround Left speaker with
connections on the left remote zone speaker and con-
be used with any source device equipped with analog
older color-coding, while the gray terminal should be
nect the tan and black SBR terminals to the red and
Y/Pr/Pb or RGB component video outputs. The factory
connected to the red (+) terminal on the Surround
black terminals on the right remote zone speaker.
default is for these jacks to be a linked to the DVD
Right speaker with the older color-coding. Connect the
black (�) terminal on the AVR to the matching black? Switched AC Accessory Outlet: These outletsinput, but you may change the setting at any time
negative (�) terminals for each surround speaker.(Seemay be used to power any device you wish to havethrough the IN/OUT SETUP menu.See
page 16 for more information on speaker polarity.)turned on when the AVR630 is turned on with thepage 21 for more information on configuring the
Standby/On Switch 1.component video inputs.
? Front Speaker Outputs: Connect these outputs
d Component Video 2 Inputs: These inputs may
to the matching + or � terminals on your left and right¤ Unswitched AC Accessory Outlet: This outlet
be used with any video source device equipped with
speakers. When making speaker connections alwaysmay be used to power any AC device. The power will
analog Y/Pr/Pb or RGB component video outputs. The
make certain to maintain correct polarity by connectingremain on at this outlet regardless of whether the
factory default is for these jacks to be a linked to the
the color-coded (white for front left and red for frontAVR 630 is on or off.
Video 2 input, but you may change the setting at any
right) (+) terminals on the AVR630 to the red (+)
NOTE: The total power consumption of all devicestime through the IN/OUT SETUP menu.See
terminals on the speakers and the black (�) terminals
connected to the accessory outlets should not exceedpage 21 for more information on configuring the com-
on the AVR630 to the black (�) terminals on the
100 watts.ponent video inputs.
speakers.See page 16 for more information on
speaker polarity.? AC Power Cord Jack: Connect the AC powere RS-232 Port: This jack may be used to control
the AVR 630 over a bi-directional RS-232 serial
cord to this jack when the installation is complete.
? Fan Vents: These ventilation holes are the output
control link to a compatible computer or programmable
To ensure safe operation, use only the power cord
of the AVR 630Os airflow system. To ensure proper
remote control system. Due to the complexity of
supplied with the unit. If a replacement is required,
operation of the unit and to avoid possible damage to
programming RS-232 commands we strongly
delicate surfaces, make certain that these holes areit must be of the same type and capacity.
recommend that connections to this port for
not blocked and that there is at least three inches of
? Video Monitor Outputs: Connect these jacks tocontrol purposes be made by a trained and qualified
open space between the vent holes and any wooden
the composite or S-Video input of a TV monitor ortechnician. This jack may also link to a compatible
or fabric surface. It is normal for the fan to remain off
video projector to view the on-screen menus and thecomputer to upgrade the software and operating sys-
at most normal volume levels. An automatic tempera-
output of any standard video source selected by thetem of the AVR 630 when appropriate upgrades are
ture sensor turns the fan on only when it is needed.
receiverOs video switcher.available.
f Multiroom IR Input: Connect the output of an IR
? DVD Video Inputs: Connect the composite or S-
sensor in a remote room to this jack to operate the
Video outputs of a DVD player or other video source
AVR 630Os multiroom control system.
to these jacks.
REAR-PANEL CONNECTIONS 9
10 |
ACEC
